Products
Wall - Mounted Water Ingress Testing Equipment IPX1 To IPX4 Vertical Drip And Oscillating Tube
Products Description
IPX1 to IPX4 Comprehensive Open Type Water Ingress Testing System
Overview:
The water ingress testing system is used to verify the protective performance of the enclosure for electronic and electrical products, automobiles, motorcycle parts, household appliances, seals and lamps under water dripping at degree IPX1 & IPX2 and water spraying and splashing at degree IPX3 & IPX4.
The water ingress testing system ensures that the dripping speed or spraying speed reaches the standard required value by controlling the water supply flow, the test equipment can produce a uniform flow of water drops over the whole area of the enclosure (IPX1 and IPX2) or make the enclosure of the specimen to be splashed in all directions (IPX3 and IPX4).
Standards compliant:
IEC 60529-2013 “Degrees of protection provided by enclosure (IP code)” IPX1, IPX2, IPX3 and IPX4
IEC 60598-1-2017 “Luminaries-Part1: General requirements and tests”
Structure:
The test equipment consists of a drip mechanism, an oscillating mechanism, an electrical control cabinet and a turntable. The bracket of drip box is wall-hanging and with anti-drop function, which can lift automatically controlled by motor. One end of the oscillating mechanism is mounted on the wall, and the other end of the oscillating mechanism is fixed on the floor support, the tube is caused to oscillate by motor driving. The turntable has a rotation speed of 1r/min, used for IPX1 ~IPX4 test; the turntable can be tilted 15°, used for IPX2 test. The test equipment is equipped with a water filter cleaning device to prevent pinhole blockage. This whole system adopts open type structure.
Technical parameters:
IPX3:over an arc of 60° either side of the center point (120°)
IPX4:over the whole 180° of the semicircle
Hole spacing: 50mm
IPX3:4s /cycle(2×120°);
IPX4:12s /cycle(2×350°);
IPX1 & IPX2
Drip Area
WD=1000×600mm, other sizes can be customized
Drip Height
200mm distance of the needle to the sample is automatically measured by infrared sensor
Drip Speed / Water Flow
1+0.5 0mm/min or 3+0.5 0mm/min switchable, rainfall is digitally controlled
Needle Pinhole Aperture
Φ0.4mm
Drip Hole Spacing
20mm×20mm
Drip Box Lifting
Driven by motor, adjustable from 1100-1800mm, screw guide ensures smooth lifting and self-locking
IPX3 & IPX4
Oscillating Tube
R200, R400, R600, R800, R1000, R1200, R1400, R1600mm are optional, made of stainless steel
Needle Pinhole Aperture
Φ0.4mm
Spray Holes Distribution
IPX3/4 Switching
Switching by changing a certain number of blind hole needles or through-hole needles
Oscillating Angle
IPX3:120°(±60°)； IPX4:350°(±175°)
Oscillating Speed
Water Flow
1-10L/min adjustable
General
Control & Operation
PLC and touch screen intelligent control system
Turntable
Diameter: Φ600mm, can be tilted 15°, rotating speed 1r/min, with lifting support frame, bearing capacity ≤50kg
Test Duration
0-99.9min, can be preset
Pressure Guage
0~0.25MPa
Water Storage System
The control box and water storage tank are built in one cabinet, the water storage tank is equipped with a water level float valve to automatically control the water inlet, and has high and low water level alarm detection, to effectively prevent the pump from being damaged due to dry water.
Optional
The hand-held spray nozzle as per IEC 60529 figure 5 can be configured
Safety Protection
Phase sequence protection, leakage protection, water shortage protection, abnormal protection
